Mixing in agitated tanks represents a fundamental part of
the chemical, petrochemical, pharmaceutical, food and
paper industries. This unit operation is commonly carried
out under steady flow conditions with the impeller
centered with respect to the vessel and rotating at constant
speed in one direction only. Mixing has been a popular
subject for the last years. Most studies have been focused
on power consumption, measurements of mixing times
and visualization of flow patterns. A number of techniques
have been developed for visualizing flow patterns in
stirred vessels. Mavros (2001) reviewed the use of very
sophisticated techniques for observing the flow behaviour
in stirred vessels including particles image velocimetry
(PIV), planar laser induced fluorescence (pLIF) and
thermal pulses, among others.
Mixing operations are usually carried out in some
applications at low to moderate Reynolds number, in
which the turbulent regime cannot be achieved. The
presence of important segregated regions and dead zone
generated with open impellers at low Reynolds number
has been extensively reported in the literature (Solomon et
al., 1981; Lamberto et al., 1996). Such pathologies persist
even if baffles and mixed flow impellers are used resulting
in very long mixing times, high energy consumption and
undesirable by-products due to poor reaction selectivity
can be generated. The most common way to vanish and
eliminate these regions consists of increasing the
rotational speed, however, this leads to an energy
consuming process, long mixing times, and in some cases
it may be detrimental to the final product especially when
mixing shear sensitive media.
It has been demonstrated that the flow structures generated
under steady flow conditions can be destroyed if the flow
is continuously perturbed if the impeller is lightly
displaced from tank centreline in the radial direction as
well as by using time-dependent revolutions. The works
reporting the use of spatial and temporal conditions
promoting chaotic flows in stirred vessels are reviewed in
this paper.
STEADY-STATE FLOW
Mixing operations are usually carried out at low to
moderate Reynolds number. The presence of important
segregated regions and dead zone generated with open
impellers at low Reynolds number has been extensively
reported in the literature (Solomon et al., 1981; Lamberto
et al., 1996). Those pathologies persist even if baffles and
mixed flow impellers are used resulting in very long
mixing times, high energy consumption and undesirable
by-products due to poor reaction selectivity can be
generated. The most common way to enhance mixing by
minimizing the effect of such non-homogeneities consists
of using wide impeller or increasing the rotational speed.
However, the latter option leads to high-energy levels and
in some cases it could be detrimental for materials
sensitive to shear.
Solomon et al (1981) reported for the first time the
observations of well-mixed regions around the impellers
surrounded by stagnant fluid, which are known as caverns
in the case of yield stress fluids. Considering a cavern as a
sphere with center on a Rushton turbine they proposed
empirical expressions for determining the geometrical
characteristics of such flow structures. The observations of
these flow structures were later confirmed by Alvarez et al
(2002) and Ascanio et al (2002).
UNSTEADY-STATE FLOW
The most common way to enhance mixing by minimizing
the effect of flow structures such caverns (well-mixed
regions) and isolated regions (static or quasi-static zones)
consists of using wide impellers or by increasing the
rotational speed. However, the latter option leads to highenergy
levels and in some cases it could be detrimental for
materials sensitive to shear. Therefore, other alternatives
based on the theory of chaos principles have been
developed and reported in the literature. They consist
basically on the use of spatial and temporal scenarios as
described below.

Eccentric impellers
Different alternatives based on pioneering studies on
chaotic laminar mixing have been reported in the
literature, in which it was demonstrated that
homogenization could be quickly achieved by using
eccentric cylinders rotating alternatively in both directions
during short times (Ottino et al 1988; Swanson and Ottino
1990; Muzzio et al 1991; Muzzio et al 1992). One of the
main reasons of using eccentric impellers is that they
provide the best mixing action where a vortex is not
required or not desirable.
Alvarez et al (2002) proposed the use of spatial conditions
based on the radial position of the impeller with respect to
the tank centreline. They showed that a minimal radial
displacement of the impeller can enhance the mixing
performance in terms of the mixing times. Similar results
were found by Ascanio et al (2002) by using different one
or two off-centered impellers in the stirred vessel.
Dynamic perturbations
Lamberto et al 1996 proposed the use of time-dependent
stirring speed to destroy the caverns generated under
steady mixing conditions. They demonstrated that the
mixing of Newtonian fluids could be clearly enhanced if
the fluid dynamics was continuously perturbed. This
method was shown to prevent the formation of segregated
regions close to the impeller, confirming the theoretical
results of Aref (1984). Using time-dependent rotation
directions changes conditions, Ascanio et al (2002)
demonstrated that segregated regions can be gradually
vanished and finally destroyed if the flow is continuously
perturbed.
It is clear from the above contributions based on the
fundamental concepts of chaos theory that nonconventional
mixing strategies appear to be promising to
enhance mixing in stirred tanks in laminar regime. During
the symposium a general overview of the works reporting
scenarios based spatial and temporal conditions will be
given for preventing the formation of coherent segregated
regions in the vicinity of the impeller resulting in energyefficient
processes.

PVC is in terms of revenue one of the most important
products of the chemical industry. Globally over 50% of
PVC manufactured is used in construction. Worldwide
80 % Percent of PVC is produced by suspension
polymerisation. In such processes mechanical agitation is
used to mix the monomer droplets into an aqueous liquid
phase. Growing markets and growing economies lead to
higher PVC production rates. Limits and demands in
space and transportation are changing the outfit of the
used mixing reactors. The height (H) is increasing with
constant diameter (D). Did most of the apparatuses start
with a ratio of height vs. diameter of one, ratios of two to
three are normal today and ratios of over four are expected
for the nearer future. Such unique geometries need to
fulfil the still growing exigencies in economy and
ecology. Therefore the analysis and optimisation of such
liquid/liquid systems is of major interest for the chemical
industry.
The step of scaling up a reactor from pilot plant to
industrial scale is an issue where much empiricism is still
used and where expensive and time-consuming
experimental programs are usually required [VivaldoLima
et al. 1997] and only accurate prediction of system
behaviour will change that situation. To develop such
prediction methods cooperation was set up between the
Vinnolit GmbH & Co. KG and the TU-Berlin.
From the different tasks for scale up and for the
production process of PVC the dispersion of the two
immiscible liquids is of major interest for this work. So
the drop size distributions of two model systems,
chlorobutanol/water and toluene/water, were analysed.
Here parameter variation for reactor height vs. diameter
(1.0 to 4.5), stirrer type (Rushton turbine, Retreat Curve
Impeller, single and multi-stage stirrer systems),
dissipation rate, dispersed phase fraction (5 to 50 Percent)
and influence of colloids were carried out for the named
systems. For the mathematical description of such drop
size distributions (DSD) a quantitative understanding of
drop breakage and coalescence mechanisms is essential to
develop predictive models. The mathematical model used
here is the Population Balance Equation (PBE).
After adaptation and enhancements of classical models
from the literature (Coulaloglou & Tavlarides 1977;
Kumar & Ramkrishna 1996, Alopaeus et al. 2002)
simulations for the presented system were carried out. The
use of colloids is inevitable for the suspension
polymerisation and resulting in a strong inhibition of
coalescence. So a major focus on breakage submodels of
the PBE was set. Therefore single drop breakage events

were carried out to analyze crucial influence parameters of
the breakage rate like breakage time and energy
dissipation rate. These results were used to validate and
enhance the breakage submodels of the PBE. Then the
simulation results from different models were compared
with the experimental data and each other.
METHODS
A special in-situ endoscope technique has been developed
[Ritter & Kraume 2000; Maaß et al. 2007b]. With this
technique, drop size distributions for all phase fractions
even under transient conditions can be determined with
high time resolution . The Population Balance
Equation is applied with the intention to calculate these
transient drop size distributions in the stirred system. In
order to solve the transient space averaged PBE, the
commercial numerical solver PARSIVAL® (Particle Size
Evaluation) [Wulkow et al. 2001] is applied. For the
parameter estimation the experimental data of the stirred
vessel are used. The fitted parameters had to be
significant, i.e. the confidence interval was required to be
small compared to the value of the parameter, and they
had to be independent from each other.
The single drop experiments are carried out in an in house
developed breakage cell (Maaß et al. 2007a).

Microencapsulation is a widespread technology that has many applications, like the protection and controlledrelease
of active ingredients in the medical and cosmetics industries, or the fabrication of fragranced fabrics in the
textile industry.
This work focuses on the emulsification step of an interfacial polymerization microencapsulation process. Firstly,
an emulsion is prepared that comprises a population of droplets. This dispersed phase contains a monomer. In a
second step, another monomer, which is soluble in the continuous phase, is added to the system to begin the
reaction at the interface of droplets.
In industry, microencapsulation by interfacial polymerization is usually performed in stirred-tank reactors, where
both the emulsification and encapsulation steps are carried out. But this process is very costly in energy due to
the power input necessary for the generation of a fine dispersion, as well as the time needed to get the right drop
size distribution. Moreover, the characteristics of the final product, such as the particle size distribution with
respect to the target size, and the membrane thickness and structure, are not necessarily well controlled. These
characteristics are strongly dependant on the hydrodynamic conditions of the different steps. In particular, it is
crucial to control the drop size of the emulsion in order to control the microcapsule size distribution resulting from
this process.
In this study, the emulsification process is carried out using Sulzer SMX mixers. Such mixers are usually
employed for the dispersion of viscous liquids in the laminar flow regime. However, it is demonstrated in this study
that they are also well adapted for liquid-liquid dispersion in turbulent flow.
The influence of the dispersed phase concentration, the flow velocity and the number of mixing elements on the
drop size distribution under various turbulent flow conditions is investigated. The drop size distribution is
characterized in terms of the mean surface-volume drop diameter and standard deviation, which are measured
with a laser diffraction device. The emulsions are cyclohexane-in-water stabilised with Tween 80, which are the
same fluids involved in the system chosen for the encapsulation process.
A correlation of the Sauter mean diameter with the Weber number and the Reynolds number is proposed for the
flow rate range studied and compared with the correlation given by Streiff (1977) for SMV Sulzer mixers at low
energy input.
The dispersion process in turbulent flow is governed by the ratio of the stress forces outside the drop to the
surface forces at the interface of the drop. The external stress forces are the turbulent drag forces on the drop
surface created by local velocity differences, which are promoted by turbulent eddies. In this case, the smallest
drop size corresponds to the microscale of turbulence and the size can be correlated with the specific energy
dissipation in the mixer. The specific energy can be determined from flowrate and pressure drop through the static
mixer.
Since the correlations available to calculate the pressure drop in SMX mixers are valid for single phase Newtonian
fluid flow, the pressure drop of the liquid-liquid flow is measured in this study and used to calculate the specific
energy dissipation. A correlation of the maximum drop diameter with specific energy dissipation is proposed and
compared with that given by Hinze (1955) for isotropic turbulent flow.
Finally, the minimum number of mixer elements required to obtain a stable drop diameter is given for different
hydrodynamic conditions and dispersed phase concentrations.
The work carried out has enabled the emulsification conditions in the static mixer to be optimized, which should
allow the encapsulation process to be performed in the best conditions. Moreover, the SMX static mixers show
good performance for emulsification in turbulent flow in terms of droplet size and energy consumption compared
with the conventional stirred-tank reactor.